How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
In this article in the next paragraph yow will discover a good deal of amazing information in relation to A Step-by-Step Guide to Installing a Bathtub.
Installing a tub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the task can relocate speedily; if you have to open a wall to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make sure you have actually certified yourself for the task and are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This post will aid you mount a brand-new bathtub in your bathroom if you have already acquired a brand-new tub as well as do not need to alter the setup of your previous water supply pipelines.
Your devices and also product list must make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly come from the pipelines. When the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in location in between the tap as well as the sink. Protect the faucet in place with the maker given backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap adapters. The previous type should be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Activate the water as well as examine all joints and brand-new pipework for leakages and tighten them if necessary. Load the bath tub as well as additionally examine the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly settle it into its final placement.
Planning for the Installment
First of all, the supporting structure provided with the bathroom ought to be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last placement.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bath as well as the tiling, causing complications with dampness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to permit the movement experienced when the tub is in usage. The sealer can crack fairly early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently available on the market. It is a good idea to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent reader about Installing A Bathtub, I thought sharing that article was really useful. Sharing is caring. Helping people is fun. Thank you so much for your time invested reading it.
Schedule Here Report this page